A furnace pilot light usually keeps going out because of a dirty pilot opening, a faulty or misaligned thermocouple, a draft near the furnace, low gas pressure, or a malfunctioning gas valve. A one-time outage may be caused by a temporary draft, but repeated outages indicate a problem that should be inspected.
Because the pilot assembly is part of a gas-burning appliance, safety comes first.
If you smell rotten eggs, hear hissing, or suspect a gas leak, do not attempt to relight the furnace. Leave the property immediately and call 911 and your gas utility from a safe location. Do not operate lights, appliances, phones, or switches while leaving.
NIPSCO advises customers who smell gas to stop what they are doing, leave immediately, and call for help from a safe location. Review NIPSCO’s natural gas safety guidance.
Does Your Furnace Actually Have a Pilot Light?
Standing pilot lights are generally found in older gas furnaces. They burn continuously and ignite the main burners when the thermostat calls for heat.
Most newer furnaces use an electronic ignition system instead. Depending on the furnace, this may be a hot-surface igniter or an intermittent pilot that operates only when heat is needed.
If your newer furnace won’t ignite, the problem may involve the electronic igniter, flame sensor, control board, pressure switch, or another component, not a pilot light. Carrier provides a helpful overview of the differences in its furnace pilot light guide.
Check the equipment label, owner’s manual, or manufacturer’s instructions if you are unsure which ignition system your furnace uses.
Five Common Reasons a Furnace Pilot Light Goes Out
1. A Dirty or Clogged Pilot Opening
Gas reaches the pilot flame through a small opening. Dust, soot, or other debris can restrict that opening, producing a weak or irregular flame that cannot remain lit.
A dirty pilot opening may cause the flame to look yellow, flicker, or fail to reach the thermocouple properly. Because cleaning the pilot assembly involves a gas-burning component, it should be handled during professional furnace service.
2. A Faulty or Misaligned Thermocouple
The thermocouple is a safety device positioned next to the pilot light. When heated, it tells the gas valve that a flame is present. The thermocouple closes the gas supply when the flame goes out.
A dirty, misaligned, or failed thermocouple may incorrectly signal that no flame is present. The gas valve then closes, causing the pilot to go out shortly after it is lit.
This is especially likely when the pilot ignites but goes out as soon as the pilot control is released. Thermocouple inspection, adjustment, and replacement should be left to a qualified technician.
3. A Draft or Airflow Problem
A strong air current can extinguish a small standing flame. Possible sources include:
- An open basement or utility-room window
- Gaps around doors or windows
- Air movement from nearby fans
- Duct leakage near the furnace
- A venting or chimney problem that disrupts combustion airflow
Closing an obviously open window is reasonable. Do not block combustion-air openings or alter furnace venting in an attempt to stop a draft. Improper ventilation can create a carbon monoxide hazard.
4. Low or Inconsistent Gas Pressure
The pilot cannot remain stable without an adequate supply of gas. Low pressure, a utility interruption, a regulator problem, or an issue elsewhere in the gas supply may cause the flame to weaken or disappear.
If multiple gas appliances are not working, check whether your utility has reported an outage. Do not attempt to adjust the gas regulator, gas line, or furnace controls yourself.
5. A Malfunctioning Gas Valve
The furnace gas valve controls fuel delivery to the pilot and main burners. If it is sticking, damaged, or failing electrically, it may not provide consistent gas flow.
Gas-valve diagnosis and replacement require specialized training and should always be handled by a licensed HVAC professional.
Is It Safe to Relight the Pilot Light Yourself?
You may be able to relight a standing pilot if all of the following are true:
- You do not smell gas or hear hissing.
- No carbon monoxide alarm is sounding.
- The furnace has a standing pilot light.
- The manufacturer provides clear relighting instructions.
- You feel comfortable following those instructions exactly.
Use the directions printed on the furnace or provided in its owner’s manual. Ignition procedures and required waiting periods vary by model, so generic instructions should not replace the manufacturer’s guidance.
Attempt to relight the pilot only once. If it will not light or goes out again, stop. Repeated relighting will not correct a faulty thermocouple, restricted pilot opening, gas-pressure problem, or defective valve.
Do not disassemble the pilot assembly, sand the thermocouple, adjust the gas valve, or use makeshift tools around the burner compartment.
When Should You Call an HVAC Technician?
Call an HVAC technician to schedule professional furnace repair when:
- The pilot will not ignite
- The flame goes out repeatedly
- The pilot goes out when the control is released
- The flame is weak, yellow, orange, or unstable
- You see soot or corrosion around the burner area
- The furnace starts and stops without heating the home
- The manufacturer does not provide relighting instructions
- Your furnace uses electronic ignition rather than a standing pilot
A technician can inspect the pilot assembly, thermocouple, gas valve, gas pressure, burners, venting, and safety controls to identify the actual cause.
Does a Pilot Light Problem Mean You Need a New Furnace?
Usually, no. A dirty pilot opening or failed thermocouple can often be repaired without replacing the furnace.
Replacement may be worth discussing if the inspection finds a serious safety problem, major component failure, unavailable replacement parts, or a broader pattern of expensive repairs and unreliable performance. Furnace age should be considered alongside condition, safety, repair history, and cost—not used as the sole reason for replacement.
If replacement becomes the more practical option, Siemer can explain your furnace installation and replacement choices without pressuring you into unnecessary equipment.
How Can You Prevent Future Pilot Light Problems?
Regular maintenance gives a technician an opportunity to inspect the furnace before the heating season. Depending on the system, service may include checking the pilot or ignition components, burners, gas connections, safety controls, airflow, heat exchanger, and venting.
Homeowners can also:
- Keep the area around the furnace clear
- Replace the air filter at the recommended interval
- Avoid blocking combustion-air openings
- Keep exterior exhaust and intake openings unobstructed
- Test carbon monoxide alarms regularly
- Schedule a professional inspection each year
Learn more about Siemer’s furnace tune-ups and Preferred Customer Program.
Schedule Furnace Service in Northwest Indiana
If your furnace pilot light will not stay lit, stop repeatedly relighting it. Siemer Heating, Cooling & Plumbing can inspect the furnace, identify the underlying problem, and explain the repair options.
Call us or request furnace service online. Siemer provides 24/7 emergency assistance throughout Northwest Indiana and the surrounding service area.